BEGINNER'S PLUMBING: WHAT YOU NEED FOR INSTALLING A BATHTUB

Beginner's Plumbing: What You Need for Installing a Bathtub

Beginner's Plumbing: What You Need for Installing a Bathtub

Blog Article

Book

Everyone has their private idea when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is easily obtainable, the job can relocate quickly; if you need to open a wall to remove the old tub as well as position the new tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub and also embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have already acquired a new bathtub and also don't need to change the setup of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite problematic due to the restricted gain access to that is often the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
    Prior to going on to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
    If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap and also the sink. Protect the faucet in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Setting up the Bath tub


    Making use of both wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
    The following goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the bath tub up until the level reads degree.
    To install taps, fit all-time low of the furthest versatile faucet connector to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
    Turn on the water supply and also inspect all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill up the bathtub and additionally check the overflow electrical outlet and also the typical outlet for leakages.
    Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub must wait up until the bathtub has been made use of at the very least when as this will resolve it right into its last setting.

    Getting ready for the Installation


    To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
    Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final placement.

    Tiling Around the Bath tub


    In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a stiff seal, causing the water to permeate the wall surface in between the bath and also the tiling, causing issues with wetness as well as feasible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather early if you do not take into account this activity before securing.
    Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    As a devoted reader on Installing A Bathtub, I was thinking sharing that piece of content was really helpful. Enjoyed our piece? Please share it. Help somebody else locate it. Thanks for going through it.


    Try Here

    Report this page